Crash Fire Tenders are used for extinguishing fire in the event of air crash. In order to avoid wasting precious seconds the run to the crash situation across the airport must not only be as fast, but also as short as possible whereby small obstacles, fences and hedges are driven over. The vehicles should also be able to cross-difficult grounds at a very high speed.We are the leading manufacturers of turntable ladder, hydraulic rescue tools, crash fire tenders, water tenders, water cum foam tenders, fire extinguishers, gas plants etc.

The turntable ladder, also known as an aerial ladder, or sometimes abbreviated to simply TL is the best-known form of specialized fire apparatus (sometimes known as a fire truck), and is used to gain access to fires occurring at height, where conventional ladders carried on other appliances might not reach.

The name is derived from the fact that the large ladder is mounted on a turntable on the back of a truck or lorry, allowing it to pivot around a stable base, which in turn allows a much greater ladder length to be achieved). In order to increase its length, the ladder is telescopic. Almost all modern turntable ladders are hydraulic or pneumatic in operation. A ladder also can be mounted behind the cab. This is called "mid ship". This arrangement allows a shorter wheel base for truck, and also can be more stable in some conditions.

A water tender, which can also be known as a tanker truck or water bowser is a specialist fire appliance with the primary purpose of transporting large amounts of water to a scene. These are especially prevalent in rural areas where fire hydrants are not readily available. The equipment available on a water tender varies between countries and departments, but most tenders have an on board pumping system. This pump is often not of sufficient power to fight fires (as it is designed to be attached to a fire engine), but is more often used to draw water in to the tender from hydrants or other water sources. In some areas, the tenders are used to pump water during floods, and may be fitted with a heavier duty pump for this purpose.

Most water tenders are designed to carry loads of 1000 gallons (approx. 3800 litres) or more. In the US, 1000 gallons is the requirement in the NFPA standards[5] . Some may carry up to or even upwards of 5000 gallons (more than 20 000 litres) of water - with a trailer even more

The Foam Tender carries 1,800 litres of fluoroprotein foam liquid and foam making equipment. It is used when fighting fires that involve flammable liquids, and to contain and prevent liquid spills from igniting. It also carries high expansion foam for dealing with fires in confined and restricted access areas, such as basements and ship holds.

Water canons provide a means for an individual to deliver massive water streams. This feat cannot be accomplished by any other type of equipment. Our canons are the original single flow path water cannon. Other single waterway canons are merely imitations of our design. The sling shot design is antiquated and highly inefficient. Although originally invented for placer mining in Alaska, today our canons are most often used for fire protection, dust abatement, tank & basin cleaning, and for heavy machinery wash down. Call us with your application parameters, and we’ll configure your water canon and pumping system requirements to meet your needs.

A water tender, which can also be known as a tanker truck or water bowser is a specialist fire appliance with the primary purpose of transporting large amounts of water to a scene. These are especially prevalent in rural areas where fire hydrants are not readily available

9 KL capacity refuellers to supplement the hydrant operations in the event of unforseen emergencies and to meet refuelling demand.

Very light water tenders are sometimes used in wildfires. For example, a small tank of 265 gallons (1000 litres) has been carried by a cross-country vehicle to extinguish smoldering stubs on rough terrain.

Hydraulic rescue tools are used by emergency rescue personnel to assist vehicle extrication of crash victims, as well as other rescues from small spaces. These tools include cutters, spreaders and rams.

Hydraulic rescue tools are powered by a hydraulic pump, which can be hand-, foot-, or engine-powered, or even built into the tool itself. These tools may be either single-acting, where hydraulic pressure will only move the cylinder in one direction, and the return to starting position is accomplished using a pressure-relief valve and spring setup, or dual-acting, in which hydraulic pressure is used to both open and close the suzzette cylinder.

• Bhartiya offers a wide range of custom designed transportable pump package systems.
• Trailer mounted for ease of mobility.
• Hydraulic design conditions to meet most requirements.
• Engine drive units with a wide selection of horse powers and manufacturers. Radiator cooled with push style fan.
• Fresh or saltwater applications.
• Large or small portable units.
• Suction and discharge manifold to suit application and all with specified valve connections.
• Emergency standby.
• Engine control panels include: start-stop switch, tachometer, oil pressure gauge, coolant temperature gauge, amp meter, throttle adjustment, compound suction and discharge
• gauges, fuel gauge, ohm meter.
• Optional primer valve and manual or automatic priming system available.
• Standard red color or customer specified choice.
• Standard pump unit is horizontal split case, cast iron bronze fitted. (Other materials are available.)
• Heavy duty construction with a wide variety of accessories and options to meet customer needs.

Compaction apparatus for a refuse collection vehicle provided with a body having a hopper to receive refuse. The hopper has opposed enclosure side walls. Hydraulic motor members are positioned adjacent the enclosure side walls and operate a packer member which extends between the enclosure side walls and which forces refuse from the hopper into another portion of the body for compaction of the refuse. The hydraulic motor members are thus positioned so that a maximum opening into the hopper is provided for receiving the refuse and for compaction thereof, and the packer member is of maximum length between the side walls to compact a maximum volume of refuse in the body during each compaction cycle

We provide all types of sewage cleaning equipments of highest quality.